Description:

A compressor oil range of high quality lubricants are based upon highly refined mineral oil, enhanced with additive technology providing excellent thermal and oxidative stability and good load carrying capacity, compared to other products in the same class. Aircol CM grades are formulated without zinc additives (ash less oils), recommended for the lubrication of rotary screw and reciprocating compressors.  

Advantages:

• Good water separation characteristics allows condensation to readily separate from the oil, minimizing the risk of emulsions which could block the oil separator element.  
• Fully inhibited against corrosion which enables protection even when operating under humid conditions.  
• Good thermal stability, low volatility and low carbon formation reduces the risk of fire and explosion and leads to a longer operating life (up to 4000 hours).  
• Low deposit forming tendencies extends oil change intervals and provides longer air filter life which contributes to a reduction in maintenance costs.  
• Excellent coalescing properties mean little carry over of oil in the air stream.  
• High load carrying to meet requirements of geared compressor units.  

Description:

A high performance synthetic gas compressor oil based on poly-alkylene glycol, for the lubrication of compressors handling hydrocarbon and chemical gases. The lubricant contains oxidation and corrosion inhibitors, providing excellent thermal and oxidation stability, together with the necessary corrosion protection for the compressor. 

Advantages:

Description:

A lubricant that is suitable for use in oil flooded rotary screw compressors operating under extreme climatic conditions, harsh environments and severe operating conditions where very high air discharge temperature  (> 100°C) are experienced. For normal operating conditions, these products can be used for extended drain intervals up to 8000 hours.  

Advantages:

• Increased oil service life of typically up to 8000 hours in most systems, depending on the operating environment.
• Very low deposit forming tendency, extends service life of filters and separators.
• Outstanding oxidation stability and antiwear performance providing long lubricant and equipment life.
• Ester-free formulation eliminates the formation of corrosive acids leading to longer equipment life.
• Excellent water separation characteristics allow condensation to readily separate from the oil, minimising the risk of emulsions which could block the oil separator element.
• PAO based lubricant means good compatibility with seals and mineral oil based lubricants, allowing changeover to Aircol SR without compatibility issues.  

Description:

A lubricant that is suitable for use in oil flooded rotary screw compressors operating under extreme climatic conditions, harsh environments and severe operating conditions where very high air discharge temperatures (> 100°C) are experienced. For normal operating conditions, these products can be used for extended drain intervals up to 8000 hours.  

Advantages:

Description:

A synthetic refrigeration lubricants are formulated from polyolester base stocks. They are specifically designed for use with refrigeration systems using environmentally friendly HFC refrigerants, in particular R134a. 

Advantages:

Description:

A recommendation for the lubrication of industrial gear boxes using forced circulation or splash and  oil bath lubrication. They may be used for the lubrication of spur and helical gears and in some lightly loaded worm type  gear applications.

Advantages:

• Extreme Pressure (EP) performance protect gears against wear and shock-loading as measured by FZG  performance and demonstrated extensively in the field.
• Alpha SP ‘Clean gear’ additive technology provides low deposit formation.
• Good water separation and demulsification.
• High protection against corrosion and wear.

Description:

A high quality synthetic lubricants are based on polyalpha-olefin (PAO) fluids and sulpur / phosphorus Extreme Pressure (EP) additive technology providing outstanding thermal stability and high load carrying capacity. The Alphasyn EP range has been formulated for use in all types of enclosed gears including heavy loaded / shock-loaded gears and bearings where EP properties are required. They are suitable for use in gearboxes where micropitting resistance is required and for a wide range of applications in extreme environments.  

Advantages:

• Full EP performance gives maximum protection of gears against wear and shock loading, including protection against micro pitting.
• Good thermal and oxidative stability provides reliable operation and extended operating life when compared to mineral oil based products.
• Inherently high Viscosity Index makes the product suitable for operations operating over a wide temperature range.
• Rapid air release and good performance in the Flender Foam Test prevents foaming and bearing damage.
• PAO based lubricant provides good compatibilty with seals, paints and mineral oil based lubricants.
• Excellent thermal stability and oxidation resistance.

Description:

A  gear oils that is gear oils are primarily intended for use in worm reduction gear boxes, where the low coefficient of friction of the PAG base fluid improves efficiency and consequently reduces power consumption and operating temperatures. This is particularly important in applications where sliding contact is high.

Advantages:

• Low coefficient of friction reduces energy consumption and lowers operating temperatures, this leads to longer oil life.
• Good thermal and oxidative stability provides reliable operation and extended operating life when compared to mineral oil based products.
• Inherently high VI makes the product suitable for operations over a wide temperature range.
• High load carrying capacity and good wear protection reduces maintenance.

Description:

A gear oil range of synthetic lubricants is based on polyalphaolefin (PAO) fluids and sulphur/ phosphorus anti-wear additive technology providing outstanding thermal stability and good load carrying capacity.

Advantages:

• Good thermal and oxidative stability provides reliable operation and extended operating life when compared to mineral oil based products.
• Inherently high viscosity index (VI) makes the product suitable for operations operating over a wide temperature range.
• Good anti-wear and load carrying abilities minimizes gear wear and prolongs gear tooth life.
• Reduced down time through water separation and demulsification characteristics resulting in prolonged lubricant life and increased equipment reliability.
• PAO based lubricant that provides good compatibility with seals, paints and mineral oil based lubricants.

Description:

Duratec L is a mineral based SAE 40 low ash gas engine lubricant. Duratec L is formulated primarily for spark ignition natural gas engines where a low ash formulation is specified and where the gas is largely free from aggressive components i.e. halogens and hydrogen sulphide. The detergent/dispersant additive system has been designed to control deposit formation and improve oxidation characteristics whilst protecting the engine against corrosion and offering good TBN retention.

Advantages:

• Reduces deposits & maintains engine cleanliness shown by multiple OEM engine trials and extensive field  experience.
• Possesses good thermal and oxidative stability.
• Provides good resistance to acid corrosion.
• Excellent antiwear characteristics.

Description:

Castrol Duratec M is a mineral based SAE 40 medium ash gas engine lubricant. Duratec M is for use in both spark ignition and dual-fuel gas engines. It is formulated for applications where the OEM requires a medium ash product. The detergent/dispersant additive system has been specifically designed to control deposit formation. Duratec M also has improved resistance to oxidation and nitration which ensures a longer oil service life. It also offers excellent corrosion control and TBN retention.

Advantages:

• High resistance to combustion chamber deposit formation means cleaner running engines.
• High resistance to oxidation and nitration leads to longer oil life and extends drain intervals. This reduces  maintenance costs and down time.
• Excellent antiwear characteristics provides outstanding protection against piston, cylinder wear and scuffing.

Description:

A   hydraulic oil range of shear stable high viscosity index lubricants are based on the latest stabilized zinc additive technology.

Advantages:

• High viscosity index and low pour point enables the product to be used over a wide temperature range, with good  shear stability which means no excessive loss in viscosity due to mechanical shearing.
• Excellent anti-wear performance provides extended wear protection for hydraulic pumps. Reduced down time due to  unscheduled maintenance and savings from replacement part costs.
• Excellent water separation and hydrolytic stability means reduced down time through prolonged lubricant life and  increased equipment reliability.
• Good filterability gives a cleaner system with less frequent filter changes.

Description:

A hydraulic oil range is based upon highly refined mineral oil with a low zinc containing anti-wear system.

Advantages:

• Good thermal and oxidative stability. Oxidative stability reduces deposit formation, resulting in a cleaner system. DThis can extend the machinery’s operating life.
• Excellent anti-wear performance increases wear protection, which can help reduce downtime caused by unscheduled maintenance.
• Good filterability characteristics, including in the presence of water, enables cost savings to be made from increased filter life and reduced maintenance
• Excellent water separation and hydrolytic stability, measured by industry standard testing. This increases equipment reliability, helping to prolong the lubricant’s life and reduce downtime.

Description:

Castrol MHP 153 and 154 are high performance lubricants specifically developed for use in modern highly rated marine and power generation four-stroke engines operating on distillate fuels.

Advantages:

• Long lasting protection in the toughest operating conditions.
• Enhanced performance at high temperatures.
• Potential to extend the time between overhauls so reducing costs.
• Formulated for excellent engine cleanliness.
• Cleaner piston ring zone.
• Enhanced detergency, excellent thermal and oxidative stability.
• Offers the potential to simplify and reduce overall lubricant usage.
• High load carrying capabilities and high gear performance that enables them to be used as a common oil for both engine and transmission systems.
• Reduced maintenance and wear.

Description:

Castrol Perfecto HT 5 is based on a solvent-refined, high viscosity index mineral oil specially selected for its high thermal and oxidation stability. Perfecto HT 5 is primarily intended for use in closed heat transfer systems with bulk temperatures up to 300ºC. It can also be used in open systems at much lower bulk oil temperatures. Perfecto HT 5 because of its solvency and high thermal stability serves as an excellent Turbine Flushing oil.

Advantages:

•  Tightly controlled specification helps minimize deposits in heat exchangers in order to maintain heat transfer efficiency.
• High operating temperature capability in closed systems with temperatures up to    300ºC    permitted.

Description:

The Castrol Perfecto X turbine oil range of lubricants is based upon premium quality mineral oils enhanced with rust and oxidation inhibitors to give maximum protection at high temperatures. Castrol Perfecto X grades are recommended for industrial gas turbines where the lubricant is likely to be exposed to very high localized temperatures. They are also suitable for the lubrication of steam turbines and Combined Cycle generating systems where the steam and gas turbines share a common supply. Castrol Perfecto X grades possess excellent air release performance, a high resistance to foaming and excellent water separation properties.

Advantages:

• High resistance to oxidation and thermal degradation provides a very long life lubricant because of low deposit/ lacquer formation.
• Excellent water separation and corrosion inhibition mean reduced down time through prolonged lubricant life and increased equipment reliability.
• Excellent air release properties mean they meet the requirements of all turbine manufacturers.
• Suitable for the lubrication of both gas and steam turbines makes them applicable for Combined Cycle generating stations.

Description:

Castrol Perfecto XPG 32 is formulated from unique highly refined base oils coupled with complex additive technology to provide exceptional resistance to the formation of insoluble degradation products that ultimately deposit out as varnish, however without compromise to its anti-wear performance

Advantages:

• Excellent thermal / oxidation stability even under extremes of thermal stress.
• Good water separation and corrosion inhibition performance.
• Excellent filterability minimising the possibility of additive removal even under ultra-fine filtration and the presence of moisture
• Well proven in high performance gas turbines with extensive field experience.

Description:
Castrol Spheerol AP3 is a multi-purpose lithium thickened greases containing selected mineral oils to provide excellent oxidation resistance, anti-corrosion and water resistant properties. Castrol Spheerol AP3 is bearing greases containing oxidation and corrosion inhibitors, is approved by most bearing manufacturers and widely used in industry for Automotive and Marine applications.  

Advantages:

Description:

A  lubricant that are general purpose greases designed for plant wide lubrication. The range extends from a NLGI 2 for general purpose bearing lubrication to a NLGI 00 (see separate data sheet) semi-fluid grease suitable for centralized lubrication systems and grease filled gearboxes.

Advantages:

• High mechanical stability – the grease keeps its consistency in service ensuring long lubricant life.
• Good adhesion – continuous lubrication and reduced consumption as film stays between lubricated surfaces.
• Good water resistance – the grease film remains on the surface even in the presence of water.
• Resistant to copper and steel corrosion – helps prevent rust and oxidation on metal surfaces.
• Excellent EP and anti-wear properties – protects equipment against extreme loading and helps minimize bearing component wear.

Description:
A complex calcium sulphonate grease providing superior performance benefits in the highly aggressive conditions experienced in the marine environment. Spheerol SX 2 is a true multipurpose ship machinery lubricant, specifically developed to provide enhanced lubrication and protection for bearings, wire ropes and open gears usually found in marine environments. Spheerol SX 2 is suitable for most journal bearings, wire ropes and open gears used in marine deck equipment and can be considered for roller, ball and needle bearings generally used in engine room equipment.  

Advantages:

• High drop point.  
• Excellent protection against corrosion.  
• High resistance to sea water wash off.  
  Strong adhesion to surfaces.  
• A lubricant which is solvent free containing no heavy metals or harmful constituents.  

Description:

Castrol TLX Plus is a range of high performance lubricants incorporating an advanced additive technology formulated to overcome the adverse conditions seen in engines with low oil consumption and operating with varying heavy fuel qualities.    lubricant that intended for use in a wide range of plain and rolling element bearings within both the Automotive and Industrial markets, especially targeting those application where upper operating temperatures are likely to exceed the limits of conventional, lithium thickened greases.

Advantages:

• Excellent thermal and mechanical stability ensure prolonged product integrity across a wider operating temperature range, thus enabling extended relubrication intervals and reduced maintenance.
• Good extreme pressure and anti-wear properties provide the potential for prolonged component life.
• Good water resistance provides enhanced protection in applications where the potential for exposure and contamination are higher.
• Good corrosion protection.
• Excellent multipurpose potential enabling a reduction in product inventory.

Description:

A water-based hydraulic control fluid specifically formulated for use as the control medium in subsea production control systems. The fluid incorporates all the features required for operation throughout the control system including Sub Surface Safety Valves (SSSV) and intelligent well completions.

Advantages:

• Tested according to OSPAR requirements. Rigorous environmental testing has also been completed in many geographies worldwide.
• Contains a fluorescent leak tracer to allow rapid detection of subsea leaks either visually or using a dedicated ROV mountable leak detection sensor.
• Maintains corrosion performance with seawater contamination.
• Tolerant of the high well temperatures encountered by those parts of the control system located at the well bore.
• Fully compatible and miscible in all proportions with other products in the Castrol Transaqua range and most other water-based subsea control fluids.
• Compatible with a wide range of materials commonly used in subsea control systems (see Tables 3 & 4). More detailed compatibility information is available on request.

Description:

A lubricant that is recommended for use in the automatic transmissions of a wide range of Japanese cars, light commercial vehicles and SUVs. It may be used in GM and Ford vehicles requiring Dexron III or Mercon fluids. Additionally it may be used in most European passenger Cars with 4 or 5 speed automatic transmissions.

Advantages:

• Enhanced friction durability for smooth transmission performance. 
• Exceptional high temperature protection to effectively resist fluid oxidation and the formation of deposits. 
• Superb low temperature fluidity for cold weather shifting.

Description:

An advanced mineral heavy duty diesel engine oil that is  specifically engineered to deliver longer useful oil life. It is suitable for use in high speed 4-stroke diesel engines that use a broad range of fuel qualities. It is also compatible with diesels engines fitted  with exhaust gas recirculation (EGR) system.

Advantages:

Castrol VECTON® 15W-40 CI-4/E7 with System Pro Technology™ delivers up to 45% extra performance reserve* that fights oil breakdown and also adapts to higher temperatures for longer useful oil life,  giving you confidence in your maximum drain interval. 

Modern trucks use new technologies to make as much as 30% higher torque, but that also brings  higher engine temperatures and pressures. This punishes the oil, pushing it closer to breakdown,  reducing its useful life.  Castrol VECTON® 15W-40 CI-4/E7's System Pro Technology™ formulated with  extra performance reserve fights oil breakdown by:

• Controlling oxidation and deposits

• Neutralizing harmful acids

• Maintaining viscosity

System Pro Technology™ also adapts to increased temperatures resisting viscosity loss through thermal and mechanical shear.  All of this means longer useful oil life giving you the confidence in your  maximum drain interval.  

*Compared to API and ACEA industry requirements and based on tests conducted on 81% of the Castrol VECTON range by volume using 12 months sales up to March 2017.